Orange Pi ZeroのNAS拡張ボードを買ってみた

Allwinner H2+搭載のスモールボードコンピュータOrange Pi Zeroに、SATAコネクタとmSATAコネクタ、USBポート*2、オーディオ端子、赤外線端子を増設するNAS拡張ボードを買ってみました。

Orange Pi Zero メモリ256MBモデル「Orange Pi Zero H2 Quad Core Open-source 256MB development board beyond Raspberry Pi」$6.99+送料$3.11
Orange Pi Zero メモリ512MBモデル「New Orange Pi Zero H2 Quad Core Open-source 512MB development board beyond Raspberry Pi」$8.99 +送料$3.11
Orange Pi Zero NAS拡張ボード「Orange Pi Zero NAS Expansion board Interface board Development board beyond Raspberry Pi」$6.98+送料$2.95

このNAS拡張ボードは、Orange Pi Zeroの13ピンコネクタに出てる端子全てにコネクタをつけた＋USB経由でSATAを接続する、というものです。
USB経由で接続しているため、SATAの速度は期待できない感じのものになります。

そう考えると、SATA経由でディスクを繋ぐような用途だと、直接SATAチップを制御している上位機種の「Orange Pi Plus(RAM1GB) $39.00+送料$3.41」か「Orange Pi Plus2(RAM2GB) $49.00+送料$3.00」を選択した方がいいのでは？という考えもあります。

うちの場合は、つい気の迷いで買ってしまったけど、使い道がなく眠ってるOrange Pi Zero 256MBが活用できないか？ということで買ってみました。

1/20発注で、1/28に到着、と旧正月に巻き込まれる前に発送され、到着したような感じですね。

届いたものはOrange Piのでかい方の共通箱に入ったNAS拡張ボードと、ネジセット

取り付けの為に並べてるとと・・・

ネジが３セットしかない・・・

３本をどう使うか・・・

mSATAのボードを止めるための穴と被る

添付のネジだと他の部品に当たる

どうするのが正解なのか・・・

まぁ、とりあえず電源ON

NAS拡張ボード側の電源コネクタ(EIAJ#2/PSPと同じ形状)に給電するだけで、Orange Pi Zero側にも給電されました。

で・・・ココで発注漏れが発覚。
NAS拡張ボード上の電源コネクタからSATA接続の電源をとることができるSATAケーブルの発注を忘れていました。
「SATA Line for Orange Pi not for Raspberry」$3.89+送料$2.38

これが無くても、別途電源を供給すればいいだけなんですが、コンパクトに収めようとすると必要なものですね。

現在、Orange Pi Plus2で使ってるケーブルと同じなので、機会をみて、テストしたいと思います

まずは、NAS拡張ボードだけの認識状況チェック
「armbian」をLegacy 3.4.113の最新版にして起動。
(Mainline 4.9.4の方は、まだ開発中です。「Mainline」というのはLinux kernelの標準提供版を元にしている、という意味合いです。)

Orange Pi ZeroのオンボードUSBコネクタにSDカードリーダをつけた場合

root@orangepizero:~# lsusb
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 002: ID 1976:1307 Chipsbrand Microelectronics (HK) Co., Ltd.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@orangepizero:~#

NAS拡張ボードのオーディオ端子側のUSBコネクタにSDカードリーダをつけた場合

root@orangepizero:~# lsusb
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 002: ID 1976:1307 Chipsbrand Microelectronics (HK) Co., Ltd.
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@orangepizero:~#

NAS拡張ボードのSATA端子側のUSBコネクタにSDカードリーダをつけた場合

root@orangepizero:~# lsusb
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 1976:1307 Chipsbrand Microelectronics (HK) Co., Ltd.
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@orangepizero:~#

USB機器を繋がず、lsusb -vをした結果

root@orangepizero:~# lsusb -v

Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            3.04
  iManufacturer           3 Linux 3.4.113-sun8i ohci_hcd
  iProduct                2 SW USB2.0 'Open' Host Controller (OHCI) Driver
  iSerial                 1 sunxi-ohci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             1
  wHubCharacteristic 0x0012
    No power switching (usb 1.0)
    No overcurrent protection
  bPwrOn2PwrGood        2 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
Device Status:     0x0001
  Self Powered

Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            3.04
  iManufacturer           3 Linux 3.4.113-sun8i ohci_hcd
  iProduct                2 SW USB2.0 'Open' Host Controller (OHCI) Driver
  iSerial                 1 sunxi-ohci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             1
  wHubCharacteristic 0x0012
    No power switching (usb 1.0)
    No overcurrent protection
  bPwrOn2PwrGood        2 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
Device Status:     0x0001
  Self Powered

Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            3.04
  iManufacturer           3 Linux 3.4.113-sun8i ohci_hcd
  iProduct                2 SW USB2.0 'Open' Host Controller (OHCI) Driver
  iSerial                 1 sunxi-ohci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             1
  wHubCharacteristic 0x0012
    No power switching (usb 1.0)
    No overcurrent protection
  bPwrOn2PwrGood        2 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
Device Status:     0x0001
  Self Powered

Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            3.04
  iManufacturer           3 Linux 3.4.113-sun8i ohci_hcd
  iProduct                2 SW USB2.0 'Open' Host Controller (OHCI) Driver
  iSerial                 1 sunxi-ohci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             1
  wHubCharacteristic 0x0012
    No power switching (usb 1.0)
    No overcurrent protection
  bPwrOn2PwrGood        2 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
Device Status:     0x0001
  Self Powered

Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            3.04
  iManufacturer           3 Linux 3.4.113-sun8i ehci_hcd
  iProduct                2 SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  iSerial                 1 sunxi-ehci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             1
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
Device Status:     0x0001
  Self Powered

Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            3.04
  iManufacturer           3 Linux 3.4.113-sun8i ehci_hcd
  iProduct                2 SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  iSerial                 1 sunxi-ehci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             1
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
Device Status:     0x0001
  Self Powered

Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            3.04
  iManufacturer           3 Linux 3.4.113-sun8i ehci_hcd
  iProduct                2 SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  iSerial                 1 sunxi-ehci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             1
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
Device Status:     0x0001
  Self Powered

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            3.04
  iManufacturer           3 Linux 3.4.113-sun8i ehci_hcd
  iProduct                2 SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  iSerial                 1 sunxi-ehci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             1
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
Device Status:     0x0001
  Self Powered
root@orangepizero:~#

そしてdmesgの結果。

root@orangepizero:~# dmesg
[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.4.113-sun8i (root@xenial) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.1) ) #309 SMP PREEMPT Wed Nov 9 22:05:23 CET 2016
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: sun8i
[    0.000000] cma: CMA: reserved 160 MiB at 46000000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] On node 0 totalpages: 65536
[    0.000000] free_area_init_node: node 0, pgdat c0a19740, node_mem_map c0b53000
[    0.000000]   Normal zone: 576 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 64960 pages, LIFO batch:15
[    0.000000] script_init enter!
[    0.000000] script_init exit!
[    0.000000] PERCPU: Embedded 8 pages/cpu @c0da4000 s11968 r8192 d12608 u32768
[    0.000000] pcpu-alloc: s11968 r8192 d12608 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64960
[    0.000000] Kernel command line: root=UUID=1ba508cc-2c06-4663-a8f0-25804aac8e6b rootwait rootfstype=ext4 console=tty1 console=ttyS0,115200 cgroup_enable=memory swapaccount=1 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 enforcing=0 loglevel=1 ubootpart=a725c3d4-01   sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_fb_mem_reserve=16
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] allocated 524288 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 256MB = 256MB total
[    0.000000] Memory: 78528k/78528k available, 183616k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc095c7ac   (9554 kB)
[    0.000000]       .init : 0xc095d000 - 0xc09adec0   ( 324 kB)
[    0.000000]       .data : 0xc09ae000 - 0xc0a1e590   ( 450 kB)
[    0.000000]        .bss : 0xc0a1ed44 - 0xc0b52090   (1229 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Additional per-CPU info printed with stalls.
[    0.000000] NR_IRQS:544
[    0.000000] Architected local timer running at 24.00MHz.
[    0.000000] Switching to timer-based delay loop
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [tty1] enabled
[    0.000482] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000)
[    0.000536] pid_max: default: 32768 minimum: 301
[    0.001211] Mount-cache hash table entries: 512
[    0.003147] Initializing cgroup subsys cpuacct
[    0.003179] Initializing cgroup subsys memory
[    0.003271] Initializing cgroup subsys devices
[    0.003296] Initializing cgroup subsys freezer
[    0.003318] Initializing cgroup subsys blkio
[    0.003366] Initializing cgroup subsys perf_event
[    0.003526] CPU: Testing write buffer coherency: ok
[    0.003623] ftrace: allocating 25775 entries in 76 pages
[    0.060510] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.060543] [sunxi_smp_prepare_cpus] enter
[    0.060614] Setting up static identity map for 0x406944b8 - 0x40694510
[    0.062460] CPU1: Booted secondary processor
[    0.062460] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.070394] CPU2: Booted secondary processor
[    0.070394] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.070917] CPU3: Booted secondary processor
[    0.070917] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.080334] Brought up 4 CPUs
[    0.080367] SMP: Total of 4 processors activated (19200.00 BogoMIPS).
[    0.081762] devtmpfs: initialized
[    0.095862] wakeup src cnt is : 2.
[    0.095887] [exstandby]leave extended_standby_enable_wakeup_src : event 0x800000
[    0.095910] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_map 0x0
[    0.095933] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_group 0x40
[    0.095956] [exstandby]leave extended_standby_enable_wakeup_src : event 0x800000
[    0.095978] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_map 0x8
[    0.096000] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_group 0x40
[    0.096024] sunxi pm init
[    0.096295] pinctrl core: initialized pinctrl subsystem
[    0.109020] NET: Registered protocol family 16
[    0.113058] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[    0.113193] script_sysfs_init success
[    0.113252] sunxi_dump_init success
[    0.115017] gpiochip_add: registered GPIOs 0 to 383 on device: sunxi-pinctrl
[    0.117393] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver
[    0.117393] plat: add bmp085 device
[    0.117393] plat: add pcf8591 device
[    0.117393] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.117393] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.117393] script config pll_video to 297 Mhz
[    0.117393] script config pll_de to 864 Mhz
[    0.117393] script config pll_ve to 402 Mhz
[    0.117393] sunxi_default_clk_init
[    0.117393] try to set pll6ahb1 to 200000000
[    0.117393] try to set ahb clk source to pll6ahb1
[    0.117393] set ahb clk source to pll6ahb1
[    0.117393] try to set ahb1 to 200000000
[    0.117393] try to set apb1 to 100000000
[    0.130455] bio: create slab <bio-0> at 0
[    0.130629] [ARISC] :sunxi-arisc driver v1.04
[    0.148561] [ARISC] :arisc version: [v0.1.58]
[    0.257596] [ARISC] :sunxi-arisc driver v1.04 startup succeeded
[    0.260913] SCSI subsystem initialized
[    0.261317] usbcore: registered new interface driver usbfs
[    0.261470] usbcore: registered new interface driver hub
[    0.261522] usbcore: registered new device driver usb
[    0.261522] twi_chan_cfg()340 - [twi0] has no twi_regulator.
[    0.261522] twi_chan_cfg()340 - [twi1] has no twi_regulator.
[    0.261522] twi_chan_cfg()340 - [twi2] has no twi_regulator.
[    0.261814] Linux video capture interface: v2.00
[    0.262297] Advanced Linux Sound Architecture Driver Version 1.0.25.
[    0.263765] cfg80211: Calling CRDA to update world regulatory domain
[    0.271151] Switching to clocksource arch_sys_counter
[    0.297806] FS-Cache: Loaded
[    0.298339] CacheFiles: Loaded
[    0.321594] NET: Registered protocol family 2
[    0.345297] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.346360] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.346642] TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
[    0.346944] TCP: Hash tables configured (established 8192 bind 8192)
[    0.346966] TCP: reno registered
[    0.346990] UDP hash table entries: 128 (order: 0, 4096 bytes)
[    0.347049] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[    0.347714] NET: Registered protocol family 1
[    0.348496] RPC: Registered named UNIX socket transport module.
[    0.348521] RPC: Registered udp transport module.
[    0.348539] RPC: Registered tcp transport module.
[    0.348556] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.348911] Trying to unpack rootfs image as initramfs...
[    0.918121] Freeing initrd memory: 4380K
[    0.919303] hw perfevents: enabled with ARMv7 Cortex_A7 PMU driver, 5 counters available
[    0.919542] sunxi_reg_init enter
[    0.921375] audit: initializing netlink socket (disabled)
[    0.921462] type=2000 audit(0.920:1): initialized
[    0.925193] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.925539] misc fatfs initialized
[    0.927013] NFS: Registering the id_resolver key type
[    0.927789] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.927817] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.929313] NTFS driver 2.1.30 [Flags: R/W].
[    0.929957] fuse init (API version 7.18)
[    0.931524] Btrfs loaded
[    0.931573] msgmni has been set to 481
[    0.934482] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.934523] io scheduler noop registered
[    0.934541] io scheduler deadline registered
[    0.934677] io scheduler cfq registered (default)
[    0.935476] [DISP]disp_module_init
[    0.936066] cmdline,init_disp=
[    0.936128] cmdline,disp=
[    0.944593] [DISP] Fb_map_kernel_logo,line:932:Fb_map_kernel_logo failed!
[    0.960721] Console: switching to colour frame buffer device 90x36
[    0.978904] [DISP]disp_module_init finish
[    0.979337] sw_uart_get_devinfo()1503 - uart0 has no uart_regulator.
[    0.979370] sw_uart_get_devinfo()1503 - uart1 has no uart_regulator.
[    0.979399] sw_uart_get_devinfo()1503 - uart2 has no uart_regulator.
[    0.980574] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
[    0.980602] sw_uart_pm()890 - uart0 clk is already enable
[    0.980638] sw_console_setup()1233 - console setup baud 115200 parity n bits 8, flow n
[    0.980906] console [ttyS0] enabled
[    0.981573] uart1: ttyS1 at MMIO 0x1c28400 (irq = 33) is a SUNXI
[    0.982086] uart2: ttyS2 at MMIO 0x1c28800 (irq = 34) is a SUNXI
[    0.983186] sunxi_cmatest_init enter
[    0.983265] sunxi_cmatest_init success
[    0.991660] brd: module loaded
[    0.999800] loop: module loaded
[    1.000401] sunxi_spi_chan_cfg()1376 - [spi-0] has no spi_regulator.
[    1.000431] sunxi_spi_chan_cfg()1376 - [spi-1] has no spi_regulator.
[    1.001536] spi spi0: master is unqueued, this is deprecated
[    1.002211] tun: Universal TUN/TAP device driver, 1.6
[    1.002233] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.003960] PPP generic driver version 2.4.2
[    1.004298] PPP BSD Compression module registered
[    1.004319] PPP Deflate Compression module registered
[    1.009066] PPP MPPE Compression module registered
[    1.009099] NET: Registered protocol family 24
[    1.009233] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.029418] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.029491] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus number 1
[    1.030544] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000
[    1.050068] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00
[    1.051287] hub 1-0:1.0: USB hub found
[    1.051335] hub 1-0:1.0: 1 port detected
[    1.072091] sunxi-ehci sunxi-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.072154] sunxi-ehci sunxi-ehci.2: new USB bus registered, assigned bus number 2
[    1.072941] sunxi-ehci sunxi-ehci.2: irq 106, io mem 0xf1c1b000
[    1.090070] sunxi-ehci sunxi-ehci.2: USB 0.0 started, EHCI 1.00
[    1.091182] hub 2-0:1.0: USB hub found
[    1.091237] hub 2-0:1.0: 1 port detected
[    1.111986] sunxi-ehci sunxi-ehci.3: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.112048] sunxi-ehci sunxi-ehci.3: new USB bus registered, assigned bus number 3
[    1.112837] sunxi-ehci sunxi-ehci.3: irq 108, io mem 0xf1c1c000
[    1.130071] sunxi-ehci sunxi-ehci.3: USB 0.0 started, EHCI 1.00
[    1.131124] hub 3-0:1.0: USB hub found
[    1.131174] hub 3-0:1.0: 1 port detected
[    1.151909] sunxi-ehci sunxi-ehci.4: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.151969] sunxi-ehci sunxi-ehci.4: new USB bus registered, assigned bus number 4
[    1.152730] sunxi-ehci sunxi-ehci.4: irq 110, io mem 0xf1c1d000
[    1.170062] sunxi-ehci sunxi-ehci.4: USB 0.0 started, EHCI 1.00
[    1.171140] hub 4-0:1.0: USB hub found
[    1.171188] hub 4-0:1.0: 1 port detected
[    1.171964] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.192128] sunxi-ohci sunxi-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    1.192190] sunxi-ohci sunxi-ohci.1: new USB bus registered, assigned bus number 5
[    1.192256] sunxi-ohci sunxi-ohci.1: irq 105, io mem 0xf1c1a400
[    1.255135] hub 5-0:1.0: USB hub found
[    1.255176] hub 5-0:1.0: 1 port detected
[    1.275975] sunxi-ohci sunxi-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    1.276038] sunxi-ohci sunxi-ohci.2: new USB bus registered, assigned bus number 6
[    1.276104] sunxi-ohci sunxi-ohci.2: irq 107, io mem 0xf1c1b400
[    1.335172] hub 6-0:1.0: USB hub found
[    1.335219] hub 6-0:1.0: 1 port detected
[    1.356004] sunxi-ohci sunxi-ohci.3: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    1.356064] sunxi-ohci sunxi-ohci.3: new USB bus registered, assigned bus number 7
[    1.356128] sunxi-ohci sunxi-ohci.3: irq 109, io mem 0xf1c1c400
[    1.415089] hub 7-0:1.0: USB hub found
[    1.415130] hub 7-0:1.0: 1 port detected
[    1.435831] sunxi-ohci sunxi-ohci.4: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    1.435891] sunxi-ohci sunxi-ohci.4: new USB bus registered, assigned bus number 8
[    1.435958] sunxi-ohci sunxi-ohci.4: irq 111, io mem 0xf1c1d400
[    1.495035] hub 8-0:1.0: USB hub found
[    1.495073] hub 8-0:1.0: 1 port detected
[    1.495781] Initializing USB Mass Storage driver...
[    1.496244] usbcore: registered new interface driver usb-storage
[    1.496267] USB Mass Storage support registered.
[    1.496383] usbcore: registered new interface driver ums-alauda
[    1.496502] usbcore: registered new interface driver ums-cypress
[    1.496623] usbcore: registered new interface driver ums-datafab
[    1.496719] usbcore: registered new interface driver ums_eneub6250
[    1.496818] usbcore: registered new interface driver ums-freecom
[    1.496918] usbcore: registered new interface driver ums-isd200
[    1.497016] usbcore: registered new interface driver ums-jumpshot
[    1.497110] usbcore: registered new interface driver ums-karma
[    1.497207] usbcore: registered new interface driver ums-onetouch
[    1.497332] usbcore: registered new interface driver ums-realtek
[    1.497434] usbcore: registered new interface driver ums-sddr09
[    1.497535] usbcore: registered new interface driver ums-sddr55
[    1.497634] usbcore: registered new interface driver ums-usbat
[    1.498101]  uinput result 0 , vmouse_init
[    1.499304] mousedev: PS/2 mouse device common for all mice
[    1.499767] sunxikbd_init failed.
[    1.499791] sunxikbd_init failed.
[    1.499814] ls_fetch_sysconfig_para: ls_unused.
[    1.499832] ltr_init: ls_fetch_sysconfig_para err.
[    1.500482] [RTC] WARNING: Rtc time will be wrong!!
[    1.500503] [RTC] WARNING: use *internal OSC* as clock source
[    1.501019] sunxi-rtc sunxi-rtc: rtc core: registered sunxi-rtc as rtc0
[    1.501118] i2c /dev entries driver
[    1.501911] sunxi cedar version 0.1
[    1.501995] [cedar]: install start!!!
[    1.502389] [cedar]: install end!!!
[    1.502743] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x18)
[    1.502958] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x19)
[    1.503160] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1a)
[    1.503360] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x29)
[    1.503559] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x2a)
[    1.503762] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x2b)
[    1.503962] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4c)
[    1.504183] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4d)
[    1.504399] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4e)
[    1.504642] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x18)
[    1.504877] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x19)
[    1.505111] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x1a)
[    1.505346] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x29)
[    1.505581] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x2a)
[    1.505816] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x2b)
[    1.506050] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x4c)
[    1.506284] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x4d)
[    1.506518] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x4e)
[    1.506550] sunxi_wdt_init_module: sunxi WatchDog Timer Driver v1.0
[    1.506891] sunxi_wdt_probe: devm_ioremap return wdt_reg 0xf1c20ca0, res->start 0x01c20ca0, res->end 0x01c20cbf
[    1.507189] sunxi_wdt_probe: initialized (g_timeout=16s, g_nowayout=0)
[    1.507215] wdt_enable, write reg 0xf1c20cb8 val 0x00000000
[    1.507237] timeout_to_interv, line 167
[    1.507254] interv_to_timeout, line 189
[    1.507274] wdt_set_tmout, write 0x000000b0 to mode reg 0xf1c20cb8, actual timeout 16 sec
[    1.508111] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[    1.508511] calibrat: max_cpufreq 1200Mhz Type 0!
[    1.508538] [cpu_freq] ERR:get cpu extremity frequency from sysconfig failed, use max_freq
[    1.509147] [mmc]: SD/MMC/SDIO Host Controller Driver(v1.111 2015-4-13 15:24) Compiled in Nov  9 2016 at 22:04:14
[    1.509215] [mmc]: get mmc0's sdc_power is null!
[    1.509272] [mmc]: get mmc1's sdc_power is null!
[    1.509292] [mmc]: get mmc1's 2xmode ok, val = 1
[    1.509312] [mmc]: get mmc1's ddrmode ok, val = 1
[    1.509344] [mmc]: MMC host used card: 0x3, boot card: 0x0, io_card 2
[    1.513921] [mmc]: sdc0 power_supply is null
[    1.516659] no blue_led, ignore it!
[    1.517125] Registered led device: red_led
[    1.517357] Registered led device: green_led
[    1.517389] no led_0, ignore it!
[    1.517406] no led_1, ignore it!
[    1.517422] no led_2, ignore it!
[    1.517437] no led_3, ignore it!
[    1.517452] no led_4, ignore it!
[    1.517467] no led_5, ignore it!
[    1.517482] no led_6, ignore it!
[    1.517496] no led_7, ignore it!
[    1.519119] usbcore: registered new interface driver usbhid
[    1.519141] usbhid: USB HID core driver
[    1.527573] asoc: sndcodec <-> sunxi-codec mapping ok
[    1.529822] [DAUDIO]sunxi-daudio cannot find any using configuration for controllers, return directly!
[    1.530281] [I2S]snddaudio cannot find any using configuration for controllers, return directly!
[    1.530312] [DAUDIO0] driver not init,just return.
[    1.537349] asoc: sndhdmi <-> sunxi-hdmiaudio.0 mapping ok
[    1.539932] oprofile: using arm/armv7-ca7
[    1.540354] u32 classifier
[    1.540374]     Performance counters on
[    1.540391]     input device check on
[    1.540405]     Actions configured
[    1.540773] IPv4 over IPv4 tunneling driver
[    1.542043] TCP: bic registered
[    1.542066] TCP: cubic registered
[    1.542081] TCP: westwood registered
[    1.542097] TCP: highspeed registered
[    1.542113] TCP: hybla registered
[    1.542129] TCP: htcp registered
[    1.542144] TCP: vegas registered
[    1.542160] TCP: veno registered
[    1.542175] TCP: scalable registered
[    1.542191] TCP: lp registered
[    1.542206] TCP: yeah registered
[    1.542222] TCP: illinois registered
[    1.542237] Initializing XFRM netlink socket
[    1.542711] NET: Registered protocol family 10
[    1.545031] NET: Registered protocol family 17
[    1.545091] NET: Registered protocol family 15
[    1.545179] Registering the dns_resolver key type
[    1.546250] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    1.546293] ThumbEE CPU extension supported.
[    1.546334] Registering SWP/SWPB emulation handler
[    1.547466] registered taskstats version 1
[    1.548750] ths_fetch_sysconfig_para: type err  device_used = 1.
[    1.551454] CPU Budget:corekeeper enabled
[    1.551997] CPU Budget:Register notifier
[    1.552021] CPU Budget:register Success
[    1.552047] sunxi-budget-cooling sunxi-budget-cooling: Cooling device registered: thermal-budget-0
[    1.558416] [rf_pm]: Did not config module_power1 in sys_config
[    1.558448] [rf_pm]: Did not config module_power2 in sys_config
[    1.558470] [rf_pm]: Did not config module_power3 in sys_config
[    1.558491] [rf_pm]: mod has no chip_en gpio
[    1.558509] [rf_pm]: regulator on.
[    1.558539] [rf_pm]: set losc_out 32k out[wifi_pm]: set wl_reg_on 1 !
[    1.584390] mmc0: new high speed SDHC card at address 1234
[    1.585361] mmcblk0: mmc0:1234 SA16G 14.4 GiB
[    1.587439]  mmcblk0: p1
[    1.588524] mmcblk mmc0:1234: Card claimed for testing.
[    1.588554] mmc0:1234: SA16G 14.4 GiB
[    1.659158] [wifi_pm]: get wifi_sdc_id failed
[    1.660735] [mmc]: sdc1 power_supply is null
[    1.718620] mmc1: new high speed SDIO card at address 0001
[    1.759230] [wifi_pm]: wifi gpio init is OK !!
[    1.759337] [rfkill]: init no bt used in configuration
[    1.759357] ALSA device list:
[    1.759372]   #0: audiocodec
[    1.759387]   #1: sndhdmi
[    1.761141] Freeing init memory: 320K
[    2.349521] vmouse_input_dev_open
[    2.380259] vmouse_input_dev_close
[    3.032533] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null)
[    3.659515] systemd[1]: System time before build time, advancing clock.
[    4.190542] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[    4.191161] systemd[1]: Detected architecture arm.
[    4.221840] systemd[1]: Set hostname to <orangepizero>.
[    4.842674] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    4.860791] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[    4.880558] systemd[1]: Listening on udev Kernel Socket.
[    4.900950] systemd[1]: Listening on Journal Audit Socket.
[    4.920334] systemd[1]: Reached target Remote File Systems (Pre).
[    4.940608] systemd[1]: Listening on Journal Socket (/dev/log).
[    4.961403] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    4.980662] systemd[1]: Listening on Journal Socket.
[    5.001158] systemd[1]: Created slice User and Session Slice.
[    5.020350] systemd[1]: Reached target Encrypted Volumes.
[    5.040399] systemd[1]: Reached target Remote File Systems.
[    5.060976] systemd[1]: Created slice System Slice.
[    5.190722] systemd[1]: Starting Nameserver information manager...
[    5.310942] systemd[1]: Created slice system-serial\x2dgetty.slice.
[    5.431183] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[    5.620552] systemd[1]: Mounting POSIX Message Queue File System...
[    5.821191] systemd[1]: Starting Set console keymap...
[    5.961423] systemd[1]: Starting Load Kernel Modules...
[    6.108144] [XRADIO] Driver Label:L34M.01.08.0002  Nov  9 2016 22:04:34
[    6.108264] [XRADIO] Allocated hw_priv @ c4bff240
[    6.108523] [XRADIO_ERR] Access_file failed, path:/data/xr_wifi.conf!
[    6.109310] [SBUS] XRadio Device:sdio clk=50000000
[    6.109642] xradio wlan power on
[    6.109676] gpio wl_reg_on set val 1, act val 1
[    6.140744] systemd[1]: Mounting Debug File System...
[    6.159730] gpio wl_reg_on set val 0, act val 0
[    6.160908] systemd[1]: Listening on Syslog Socket.
[    6.161763] gpio wl_reg_on set val 1, act val 1
[    6.251177] systemd[1]: Starting Restore / save the current clock...
[    6.261874] [XRADIO] Detect SDIO card 1
[    6.270881] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    6.290876] systemd[1]: Listening on udev Control Socket.
[    6.310417] systemd[1]: Reached target Slices.
[    6.330478] systemd[1]: Listening on fsck to fsckd communication Socket.
[    6.401220] systemd[1]: Starting Remount Root and Kernel File Systems...
[    6.490769] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=600,errors=remount-ro
[    6.516200] systemd[1]: Mounted POSIX Message Queue File System.
[    6.530602] systemd[1]: Mounted Debug File System.
[    6.608405] [XRADIO_ERR] xradio_load_firmware: can't read config register, err=-110.
[    6.608439] [XRADIO_ERR] xradio_load_firmware failed(-110).
[    6.944713] xradio wlan power off
[    6.944748] gpio wl_reg_on set val 0, act val 0
[    6.994805] [XRADIO] Remove SDIO card 1
[    6.995064] mmc1: card 0001 removed
[    6.995504] [mmc]: sdc1 power_supply is null
[    7.000352] systemd[1]: Started Create list of required static device nodes for the current kernel.
[    7.160317] systemd[1]: Started Set console keymap.
[    7.181460] systemd[1]: systemd-modules-load.service: Main process exited, code=exited, status=1/FAILURE
[    7.360213] systemd[1]: Failed to start Load Kernel Modules.
[    7.400260] systemd[1]: systemd-modules-load.service: Unit entered failed state.
[    7.400475] systemd[1]: systemd-modules-load.service: Failed with result 'exit-code'.
[    7.530249] systemd[1]: Started Restore / save the current clock.
[    7.690237] systemd[1]: Started Remount Root and Kernel File Systems.
[    7.861074] systemd[1]: Started Nameserver information manager.
[    7.987147] systemd[1]: Time has been changed
[    8.151413] systemd[1]: Starting udev Coldplug all Devices...
[    8.321347] systemd[1]: Starting Load/Save Random Seed...
[    8.460600] systemd[1]: Activating swap /var/swap...
[    8.601247] systemd[1]: Starting Apply Kernel Variables...
[    8.641680] Adding 131068k swap on /var/swap.  Priority:-1 extents:2 across:204796k SS
[    8.720624] systemd[1]: Mounting FUSE Control File System...
[    8.861193] systemd[1]: Starting Create Static Device Nodes in /dev...
[    8.880995] systemd[1]: Activated swap /var/swap.
[    8.906051] systemd[1]: Mounted FUSE Control File System.
[    9.520497] systemd[1]: Started Load/Save Random Seed.
[    9.690327] systemd[1]: Started Apply Kernel Variables.
[    9.870248] systemd[1]: Started Create Static Device Nodes in /dev.
[   10.010258] systemd[1]: Started udev Coldplug all Devices.
[   10.161096] systemd[1]: Starting udev Kernel Device Manager...
[   10.180459] systemd[1]: Reached target Local File Systems (Pre).
[   10.330684] systemd[1]: Mounting /tmp...
[   10.350669] systemd[1]: Reached target Swap.
[   10.427590] systemd[1]: Mounted /tmp.
[   10.442062] systemd[1]: Started udev Kernel Device Manager.
[   10.450791] systemd[1]: Reached target Local File Systems.
[   10.510956] systemd[1]: Starting Raise network interfaces...
[   10.621427] systemd[1]: Starting Set console font and keymap...
[   10.751427] systemd[1]: Started Entropy daemon using the HAVEGE algorithm.
[   10.871501] systemd[1]: Starting Journal Service...
[   10.941075] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x77)
[   10.941165] bmp085: probe of 0-0077 failed with error -70
[   10.949746] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x48)
[   10.950138] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x48, dev addr: 0x48)
[   11.124875] systemd[1]: Found device /dev/ttyS0.
[   11.129979] vmouse_input_dev_open
[   11.152406] systemd[1]: Started Journal Service.
[   11.221231] vmouse_input_dev_close
[   11.773581] systemd-journald[234]: Received request to flush runtime journal from PID 1
[   11.992481] gmac0: probed
[   11.992918] gmac0 gmac0: eth0: eth0: PHY ID 00441400 at 0 IRQ poll (gmac0-0:00)
[   15.990281] PHY: gmac0-0:00 - Link is Up - 100/Full
root@orangepizero:~#