Orange Pi ZeroのNAS拡張ボードを買ってみた


Allwinner H2+搭載のスモールボードコンピュータOrange Pi Zeroに、SATAコネクタとmSATAコネクタ、USBポート*2、オーディオ端子、赤外線端子を増設するNAS拡張ボードを買ってみました。

Orange Pi Zero メモリ256MBモデル「Orange Pi Zero H2 Quad Core Open-source 256MB development board beyond Raspberry Pi」$6.99+送料$3.11
Orange Pi Zero メモリ512MBモデル「New Orange Pi Zero H2 Quad Core Open-source 512MB development board beyond Raspberry Pi」$8.99 +送料$3.11
Orange Pi Zero NAS拡張ボード「Orange Pi Zero NAS Expansion board Interface board Development board beyond Raspberry Pi」$6.98+送料$2.95

このNAS拡張ボードは、Orange Pi Zeroの13ピンコネクタに出てる端子全てにコネクタをつけた+USB経由でSATAを接続する、というものです。
USB経由で接続しているため、SATAの速度は期待できない感じのものになります。

そう考えると、SATA経由でディスクを繋ぐような用途だと、直接SATAチップを制御している上位機種の「Orange Pi Plus(RAM1GB) $39.00+送料$3.41」か「Orange Pi Plus2(RAM2GB) $49.00+送料$3.00」を選択した方がいいのでは?という考えもあります。

うちの場合は、つい気の迷いで買ってしまったけど、使い道がなく眠ってるOrange Pi Zero 256MBが活用できないか?ということで買ってみました。

1/20発注で、1/28に到着、と旧正月に巻き込まれる前に発送され、到着したような感じですね。

届いたものはOrange Piのでかい方の共通箱に入ったNAS拡張ボードと、ネジセット

取り付けの為に並べてるとと・・・

ネジが3セットしかない・・・

3本をどう使うか・・・

mSATAのボードを止めるための穴と被る


添付のネジだと他の部品に当たる

どうするのが正解なのか・・・

まぁ、とりあえず電源ON

NAS拡張ボード側の電源コネクタ(EIAJ#2/PSPと同じ形状)に給電するだけで、Orange Pi Zero側にも給電されました。

で・・・ココで発注漏れが発覚。
NAS拡張ボード上の電源コネクタからSATA接続の電源をとることができるSATAケーブルの発注を忘れていました。
SATA Line for Orange Pi not for Raspberry」$3.89+送料$2.38

これが無くても、別途電源を供給すればいいだけなんですが、コンパクトに収めようとすると必要なものですね。

現在、Orange Pi Plus2で使ってるケーブルと同じなので、機会をみて、テストしたいと思います

まずは、NAS拡張ボードだけの認識状況チェック
armbian」をLegacy 3.4.113の最新版にして起動。
(Mainline 4.9.4の方は、まだ開発中です。「Mainline」というのはLinux kernelの標準提供版を元にしている、という意味合いです。)

Orange Pi ZeroのオンボードUSBコネクタにSDカードリーダをつけた場合

root@orangepizero:~# lsusb
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 002: ID 1976:1307 Chipsbrand Microelectronics (HK) Co., Ltd.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@orangepizero:~#

NAS拡張ボードのオーディオ端子側のUSBコネクタにSDカードリーダをつけた場合

root@orangepizero:~# lsusb
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 002: ID 1976:1307 Chipsbrand Microelectronics (HK) Co., Ltd.
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@orangepizero:~#

NAS拡張ボードのSATA端子側のUSBコネクタにSDカードリーダをつけた場合

root@orangepizero:~# lsusb
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 1976:1307 Chipsbrand Microelectronics (HK) Co., Ltd.
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@orangepizero:~#

USB機器を繋がず、lsusb -vをした結果

root@orangepizero:~# lsusb -v

Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            3.04
  iManufacturer           3 Linux 3.4.113-sun8i ohci_hcd
  iProduct                2 SW USB2.0 'Open' Host Controller (OHCI) Driver
  iSerial                 1 sunxi-ohci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             1
  wHubCharacteristic 0x0012
    No power switching (usb 1.0)
    No overcurrent protection
  bPwrOn2PwrGood        2 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
Device Status:     0x0001
  Self Powered

Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            3.04
  iManufacturer           3 Linux 3.4.113-sun8i ohci_hcd
  iProduct                2 SW USB2.0 'Open' Host Controller (OHCI) Driver
  iSerial                 1 sunxi-ohci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             1
  wHubCharacteristic 0x0012
    No power switching (usb 1.0)
    No overcurrent protection
  bPwrOn2PwrGood        2 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
Device Status:     0x0001
  Self Powered

Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            3.04
  iManufacturer           3 Linux 3.4.113-sun8i ohci_hcd
  iProduct                2 SW USB2.0 'Open' Host Controller (OHCI) Driver
  iSerial                 1 sunxi-ohci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             1
  wHubCharacteristic 0x0012
    No power switching (usb 1.0)
    No overcurrent protection
  bPwrOn2PwrGood        2 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
Device Status:     0x0001
  Self Powered

Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0001 1.1 root hub
  bcdDevice            3.04
  iManufacturer           3 Linux 3.4.113-sun8i ohci_hcd
  iProduct                2 SW USB2.0 'Open' Host Controller (OHCI) Driver
  iSerial                 1 sunxi-ohci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             1
  wHubCharacteristic 0x0012
    No power switching (usb 1.0)
    No overcurrent protection
  bPwrOn2PwrGood        2 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
Device Status:     0x0001
  Self Powered

Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            3.04
  iManufacturer           3 Linux 3.4.113-sun8i ehci_hcd
  iProduct                2 SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  iSerial                 1 sunxi-ehci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             1
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
Device Status:     0x0001
  Self Powered

Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            3.04
  iManufacturer           3 Linux 3.4.113-sun8i ehci_hcd
  iProduct                2 SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  iSerial                 1 sunxi-ehci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             1
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
Device Status:     0x0001
  Self Powered

Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            3.04
  iManufacturer           3 Linux 3.4.113-sun8i ehci_hcd
  iProduct                2 SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  iSerial                 1 sunxi-ehci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             1
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
Device Status:     0x0001
  Self Powered

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed (or root) hub
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            3.04
  iManufacturer           3 Linux 3.4.113-sun8i ehci_hcd
  iProduct                2 SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
  iSerial                 1 sunxi-ehci
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             1
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
Device Status:     0x0001
  Self Powered
root@orangepizero:~#

そしてdmesgの結果。

root@orangepizero:~# dmesg
[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.4.113-sun8i (root@xenial) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.1) ) #309 SMP PREEMPT Wed Nov 9 22:05:23 CET 2016
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: sun8i
[    0.000000] cma: CMA: reserved 160 MiB at 46000000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] On node 0 totalpages: 65536
[    0.000000] free_area_init_node: node 0, pgdat c0a19740, node_mem_map c0b53000
[    0.000000]   Normal zone: 576 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 64960 pages, LIFO batch:15
[    0.000000] script_init enter!
[    0.000000] script_init exit!
[    0.000000] PERCPU: Embedded 8 pages/cpu @c0da4000 s11968 r8192 d12608 u32768
[    0.000000] pcpu-alloc: s11968 r8192 d12608 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64960
[    0.000000] Kernel command line: root=UUID=1ba508cc-2c06-4663-a8f0-25804aac8e6b rootwait rootfstype=ext4 console=tty1 console=ttyS0,115200 cgroup_enable=memory swapaccount=1 hdmi.audio=EDID:0 disp.screen0_output_mode=1920x1080p60 panic=10 consoleblank=0 enforcing=0 loglevel=1 ubootpart=a725c3d4-01   sunxi_ve_mem_reserve=0 sunxi_g2d_mem_reserve=0 sunxi_fb_mem_reserve=16
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] allocated 524288 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 256MB = 256MB total
[    0.000000] Memory: 78528k/78528k available, 183616k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff000000   ( 744 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc095c7ac   (9554 kB)
[    0.000000]       .init : 0xc095d000 - 0xc09adec0   ( 324 kB)
[    0.000000]       .data : 0xc09ae000 - 0xc0a1e590   ( 450 kB)
[    0.000000]        .bss : 0xc0a1ed44 - 0xc0b52090   (1229 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Additional per-CPU info printed with stalls.
[    0.000000] NR_IRQS:544
[    0.000000] Architected local timer running at 24.00MHz.
[    0.000000] Switching to timer-based delay loop
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [tty1] enabled
[    0.000482] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000)
[    0.000536] pid_max: default: 32768 minimum: 301
[    0.001211] Mount-cache hash table entries: 512
[    0.003147] Initializing cgroup subsys cpuacct
[    0.003179] Initializing cgroup subsys memory
[    0.003271] Initializing cgroup subsys devices
[    0.003296] Initializing cgroup subsys freezer
[    0.003318] Initializing cgroup subsys blkio
[    0.003366] Initializing cgroup subsys perf_event
[    0.003526] CPU: Testing write buffer coherency: ok
[    0.003623] ftrace: allocating 25775 entries in 76 pages
[    0.060510] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.060543] [sunxi_smp_prepare_cpus] enter
[    0.060614] Setting up static identity map for 0x406944b8 - 0x40694510
[    0.062460] CPU1: Booted secondary processor
[    0.062460] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.070394] CPU2: Booted secondary processor
[    0.070394] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.070917] CPU3: Booted secondary processor
[    0.070917] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.080334] Brought up 4 CPUs
[    0.080367] SMP: Total of 4 processors activated (19200.00 BogoMIPS).
[    0.081762] devtmpfs: initialized
[    0.095862] wakeup src cnt is : 2.
[    0.095887] [exstandby]leave extended_standby_enable_wakeup_src : event 0x800000
[    0.095910] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_map 0x0
[    0.095933] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_group 0x40
[    0.095956] [exstandby]leave extended_standby_enable_wakeup_src : event 0x800000
[    0.095978] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_map 0x8
[    0.096000] [exstandby]leave extended_standby_enable_wakeup_src : wakeup_gpio_group 0x40
[    0.096024] sunxi pm init
[    0.096295] pinctrl core: initialized pinctrl subsystem
[    0.109020] NET: Registered protocol family 16
[    0.113058] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[    0.113193] script_sysfs_init success
[    0.113252] sunxi_dump_init success
[    0.115017] gpiochip_add: registered GPIOs 0 to 383 on device: sunxi-pinctrl
[    0.117393] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver
[    0.117393] plat: add bmp085 device
[    0.117393] plat: add pcf8591 device
[    0.117393] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.117393] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.117393] script config pll_video to 297 Mhz
[    0.117393] script config pll_de to 864 Mhz
[    0.117393] script config pll_ve to 402 Mhz
[    0.117393] sunxi_default_clk_init
[    0.117393] try to set pll6ahb1 to 200000000
[    0.117393] try to set ahb clk source to pll6ahb1
[    0.117393] set ahb clk source to pll6ahb1
[    0.117393] try to set ahb1 to 200000000
[    0.117393] try to set apb1 to 100000000
[    0.130455] bio: create slab <bio-0> at 0
[    0.130629] [ARISC] :sunxi-arisc driver v1.04
[    0.148561] [ARISC] :arisc version: [v0.1.58]
[    0.257596] [ARISC] :sunxi-arisc driver v1.04 startup succeeded
[    0.260913] SCSI subsystem initialized
[    0.261317] usbcore: registered new interface driver usbfs
[    0.261470] usbcore: registered new interface driver hub
[    0.261522] usbcore: registered new device driver usb
[    0.261522] twi_chan_cfg()340 - [twi0] has no twi_regulator.
[    0.261522] twi_chan_cfg()340 - [twi1] has no twi_regulator.
[    0.261522] twi_chan_cfg()340 - [twi2] has no twi_regulator.
[    0.261814] Linux video capture interface: v2.00
[    0.262297] Advanced Linux Sound Architecture Driver Version 1.0.25.
[    0.263765] cfg80211: Calling CRDA to update world regulatory domain
[    0.271151] Switching to clocksource arch_sys_counter
[    0.297806] FS-Cache: Loaded
[    0.298339] CacheFiles: Loaded
[    0.321594] NET: Registered protocol family 2
[    0.345297] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.346360] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.346642] TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
[    0.346944] TCP: Hash tables configured (established 8192 bind 8192)
[    0.346966] TCP: reno registered
[    0.346990] UDP hash table entries: 128 (order: 0, 4096 bytes)
[    0.347049] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[    0.347714] NET: Registered protocol family 1
[    0.348496] RPC: Registered named UNIX socket transport module.
[    0.348521] RPC: Registered udp transport module.
[    0.348539] RPC: Registered tcp transport module.
[    0.348556] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.348911] Trying to unpack rootfs image as initramfs...
[    0.918121] Freeing initrd memory: 4380K
[    0.919303] hw perfevents: enabled with ARMv7 Cortex_A7 PMU driver, 5 counters available
[    0.919542] sunxi_reg_init enter
[    0.921375] audit: initializing netlink socket (disabled)
[    0.921462] type=2000 audit(0.920:1): initialized
[    0.925193] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.925539] misc fatfs initialized
[    0.927013] NFS: Registering the id_resolver key type
[    0.927789] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.927817] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.929313] NTFS driver 2.1.30 [Flags: R/W].
[    0.929957] fuse init (API version 7.18)
[    0.931524] Btrfs loaded
[    0.931573] msgmni has been set to 481
[    0.934482] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.934523] io scheduler noop registered
[    0.934541] io scheduler deadline registered
[    0.934677] io scheduler cfq registered (default)
[    0.935476] [DISP]disp_module_init
[    0.936066] cmdline,init_disp=
[    0.936128] cmdline,disp=
[    0.944593] [DISP] Fb_map_kernel_logo,line:932:Fb_map_kernel_logo failed!
[    0.960721] Console: switching to colour frame buffer device 90x36
[    0.978904] [DISP]disp_module_init finish
[    0.979337] sw_uart_get_devinfo()1503 - uart0 has no uart_regulator.
[    0.979370] sw_uart_get_devinfo()1503 - uart1 has no uart_regulator.
[    0.979399] sw_uart_get_devinfo()1503 - uart2 has no uart_regulator.
[    0.980574] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
[    0.980602] sw_uart_pm()890 - uart0 clk is already enable
[    0.980638] sw_console_setup()1233 - console setup baud 115200 parity n bits 8, flow n
[    0.980906] console [ttyS0] enabled
[    0.981573] uart1: ttyS1 at MMIO 0x1c28400 (irq = 33) is a SUNXI
[    0.982086] uart2: ttyS2 at MMIO 0x1c28800 (irq = 34) is a SUNXI
[    0.983186] sunxi_cmatest_init enter
[    0.983265] sunxi_cmatest_init success
[    0.991660] brd: module loaded
[    0.999800] loop: module loaded
[    1.000401] sunxi_spi_chan_cfg()1376 - [spi-0] has no spi_regulator.
[    1.000431] sunxi_spi_chan_cfg()1376 - [spi-1] has no spi_regulator.
[    1.001536] spi spi0: master is unqueued, this is deprecated
[    1.002211] tun: Universal TUN/TAP device driver, 1.6
[    1.002233] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.003960] PPP generic driver version 2.4.2
[    1.004298] PPP BSD Compression module registered
[    1.004319] PPP Deflate Compression module registered
[    1.009066] PPP MPPE Compression module registered
[    1.009099] NET: Registered protocol family 24
[    1.009233] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.029418] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.029491] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus number 1
[    1.030544] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000
[    1.050068] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00
[    1.051287] hub 1-0:1.0: USB hub found
[    1.051335] hub 1-0:1.0: 1 port detected
[    1.072091] sunxi-ehci sunxi-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.072154] sunxi-ehci sunxi-ehci.2: new USB bus registered, assigned bus number 2
[    1.072941] sunxi-ehci sunxi-ehci.2: irq 106, io mem 0xf1c1b000
[    1.090070] sunxi-ehci sunxi-ehci.2: USB 0.0 started, EHCI 1.00
[    1.091182] hub 2-0:1.0: USB hub found
[    1.091237] hub 2-0:1.0: 1 port detected
[    1.111986] sunxi-ehci sunxi-ehci.3: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.112048] sunxi-ehci sunxi-ehci.3: new USB bus registered, assigned bus number 3
[    1.112837] sunxi-ehci sunxi-ehci.3: irq 108, io mem 0xf1c1c000
[    1.130071] sunxi-ehci sunxi-ehci.3: USB 0.0 started, EHCI 1.00
[    1.131124] hub 3-0:1.0: USB hub found
[    1.131174] hub 3-0:1.0: 1 port detected
[    1.151909] sunxi-ehci sunxi-ehci.4: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.151969] sunxi-ehci sunxi-ehci.4: new USB bus registered, assigned bus number 4
[    1.152730] sunxi-ehci sunxi-ehci.4: irq 110, io mem 0xf1c1d000
[    1.170062] sunxi-ehci sunxi-ehci.4: USB 0.0 started, EHCI 1.00
[    1.171140] hub 4-0:1.0: USB hub found
[    1.171188] hub 4-0:1.0: 1 port detected
[    1.171964] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.192128] sunxi-ohci sunxi-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    1.192190] sunxi-ohci sunxi-ohci.1: new USB bus registered, assigned bus number 5
[    1.192256] sunxi-ohci sunxi-ohci.1: irq 105, io mem 0xf1c1a400
[    1.255135] hub 5-0:1.0: USB hub found
[    1.255176] hub 5-0:1.0: 1 port detected
[    1.275975] sunxi-ohci sunxi-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    1.276038] sunxi-ohci sunxi-ohci.2: new USB bus registered, assigned bus number 6
[    1.276104] sunxi-ohci sunxi-ohci.2: irq 107, io mem 0xf1c1b400
[    1.335172] hub 6-0:1.0: USB hub found
[    1.335219] hub 6-0:1.0: 1 port detected
[    1.356004] sunxi-ohci sunxi-ohci.3: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    1.356064] sunxi-ohci sunxi-ohci.3: new USB bus registered, assigned bus number 7
[    1.356128] sunxi-ohci sunxi-ohci.3: irq 109, io mem 0xf1c1c400
[    1.415089] hub 7-0:1.0: USB hub found
[    1.415130] hub 7-0:1.0: 1 port detected
[    1.435831] sunxi-ohci sunxi-ohci.4: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    1.435891] sunxi-ohci sunxi-ohci.4: new USB bus registered, assigned bus number 8
[    1.435958] sunxi-ohci sunxi-ohci.4: irq 111, io mem 0xf1c1d400
[    1.495035] hub 8-0:1.0: USB hub found
[    1.495073] hub 8-0:1.0: 1 port detected
[    1.495781] Initializing USB Mass Storage driver...
[    1.496244] usbcore: registered new interface driver usb-storage
[    1.496267] USB Mass Storage support registered.
[    1.496383] usbcore: registered new interface driver ums-alauda
[    1.496502] usbcore: registered new interface driver ums-cypress
[    1.496623] usbcore: registered new interface driver ums-datafab
[    1.496719] usbcore: registered new interface driver ums_eneub6250
[    1.496818] usbcore: registered new interface driver ums-freecom
[    1.496918] usbcore: registered new interface driver ums-isd200
[    1.497016] usbcore: registered new interface driver ums-jumpshot
[    1.497110] usbcore: registered new interface driver ums-karma
[    1.497207] usbcore: registered new interface driver ums-onetouch
[    1.497332] usbcore: registered new interface driver ums-realtek
[    1.497434] usbcore: registered new interface driver ums-sddr09
[    1.497535] usbcore: registered new interface driver ums-sddr55
[    1.497634] usbcore: registered new interface driver ums-usbat
[    1.498101]  uinput result 0 , vmouse_init
[    1.499304] mousedev: PS/2 mouse device common for all mice
[    1.499767] sunxikbd_init failed.
[    1.499791] sunxikbd_init failed.
[    1.499814] ls_fetch_sysconfig_para: ls_unused.
[    1.499832] ltr_init: ls_fetch_sysconfig_para err.
[    1.500482] [RTC] WARNING: Rtc time will be wrong!!
[    1.500503] [RTC] WARNING: use *internal OSC* as clock source
[    1.501019] sunxi-rtc sunxi-rtc: rtc core: registered sunxi-rtc as rtc0
[    1.501118] i2c /dev entries driver
[    1.501911] sunxi cedar version 0.1
[    1.501995] [cedar]: install start!!!
[    1.502389] [cedar]: install end!!!
[    1.502743] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x18)
[    1.502958] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x19)
[    1.503160] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1a)
[    1.503360] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x29)
[    1.503559] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x2a)
[    1.503762] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x2b)
[    1.503962] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4c)
[    1.504183] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4d)
[    1.504399] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4e)
[    1.504642] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x18)
[    1.504877] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x19)
[    1.505111] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x1a)
[    1.505346] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x29)
[    1.505581] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x2a)
[    1.505816] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x2b)
[    1.506050] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x4c)
[    1.506284] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x4d)
[    1.506518] sunxi_i2c_do_xfer()985 - [i2c1] incomplete xfer (status: 0x20, dev addr: 0x4e)
[    1.506550] sunxi_wdt_init_module: sunxi WatchDog Timer Driver v1.0
[    1.506891] sunxi_wdt_probe: devm_ioremap return wdt_reg 0xf1c20ca0, res->start 0x01c20ca0, res->end 0x01c20cbf
[    1.507189] sunxi_wdt_probe: initialized (g_timeout=16s, g_nowayout=0)
[    1.507215] wdt_enable, write reg 0xf1c20cb8 val 0x00000000
[    1.507237] timeout_to_interv, line 167
[    1.507254] interv_to_timeout, line 189
[    1.507274] wdt_set_tmout, write 0x000000b0 to mode reg 0xf1c20cb8, actual timeout 16 sec
[    1.508111] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[    1.508511] calibrat: max_cpufreq 1200Mhz Type 0!
[    1.508538] [cpu_freq] ERR:get cpu extremity frequency from sysconfig failed, use max_freq
[    1.509147] [mmc]: SD/MMC/SDIO Host Controller Driver(v1.111 2015-4-13 15:24) Compiled in Nov  9 2016 at 22:04:14
[    1.509215] [mmc]: get mmc0's sdc_power is null!
[    1.509272] [mmc]: get mmc1's sdc_power is null!
[    1.509292] [mmc]: get mmc1's 2xmode ok, val = 1
[    1.509312] [mmc]: get mmc1's ddrmode ok, val = 1
[    1.509344] [mmc]: MMC host used card: 0x3, boot card: 0x0, io_card 2
[    1.513921] [mmc]: sdc0 power_supply is null
[    1.516659] no blue_led, ignore it!
[    1.517125] Registered led device: red_led
[    1.517357] Registered led device: green_led
[    1.517389] no led_0, ignore it!
[    1.517406] no led_1, ignore it!
[    1.517422] no led_2, ignore it!
[    1.517437] no led_3, ignore it!
[    1.517452] no led_4, ignore it!
[    1.517467] no led_5, ignore it!
[    1.517482] no led_6, ignore it!
[    1.517496] no led_7, ignore it!
[    1.519119] usbcore: registered new interface driver usbhid
[    1.519141] usbhid: USB HID core driver
[    1.527573] asoc: sndcodec <-> sunxi-codec mapping ok
[    1.529822] [DAUDIO]sunxi-daudio cannot find any using configuration for controllers, return directly!
[    1.530281] [I2S]snddaudio cannot find any using configuration for controllers, return directly!
[    1.530312] [DAUDIO0] driver not init,just return.
[    1.537349] asoc: sndhdmi <-> sunxi-hdmiaudio.0 mapping ok
[    1.539932] oprofile: using arm/armv7-ca7
[    1.540354] u32 classifier
[    1.540374]     Performance counters on
[    1.540391]     input device check on
[    1.540405]     Actions configured
[    1.540773] IPv4 over IPv4 tunneling driver
[    1.542043] TCP: bic registered
[    1.542066] TCP: cubic registered
[    1.542081] TCP: westwood registered
[    1.542097] TCP: highspeed registered
[    1.542113] TCP: hybla registered
[    1.542129] TCP: htcp registered
[    1.542144] TCP: vegas registered
[    1.542160] TCP: veno registered
[    1.542175] TCP: scalable registered
[    1.542191] TCP: lp registered
[    1.542206] TCP: yeah registered
[    1.542222] TCP: illinois registered
[    1.542237] Initializing XFRM netlink socket
[    1.542711] NET: Registered protocol family 10
[    1.545031] NET: Registered protocol family 17
[    1.545091] NET: Registered protocol family 15
[    1.545179] Registering the dns_resolver key type
[    1.546250] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    1.546293] ThumbEE CPU extension supported.
[    1.546334] Registering SWP/SWPB emulation handler
[    1.547466] registered taskstats version 1
[    1.548750] ths_fetch_sysconfig_para: type err  device_used = 1.
[    1.551454] CPU Budget:corekeeper enabled
[    1.551997] CPU Budget:Register notifier
[    1.552021] CPU Budget:register Success
[    1.552047] sunxi-budget-cooling sunxi-budget-cooling: Cooling device registered: thermal-budget-0
[    1.558416] [rf_pm]: Did not config module_power1 in sys_config
[    1.558448] [rf_pm]: Did not config module_power2 in sys_config
[    1.558470] [rf_pm]: Did not config module_power3 in sys_config
[    1.558491] [rf_pm]: mod has no chip_en gpio
[    1.558509] [rf_pm]: regulator on.
[    1.558539] [rf_pm]: set losc_out 32k out[wifi_pm]: set wl_reg_on 1 !
[    1.584390] mmc0: new high speed SDHC card at address 1234
[    1.585361] mmcblk0: mmc0:1234 SA16G 14.4 GiB
[    1.587439]  mmcblk0: p1
[    1.588524] mmcblk mmc0:1234: Card claimed for testing.
[    1.588554] mmc0:1234: SA16G 14.4 GiB
[    1.659158] [wifi_pm]: get wifi_sdc_id failed
[    1.660735] [mmc]: sdc1 power_supply is null
[    1.718620] mmc1: new high speed SDIO card at address 0001
[    1.759230] [wifi_pm]: wifi gpio init is OK !!
[    1.759337] [rfkill]: init no bt used in configuration
[    1.759357] ALSA device list:
[    1.759372]   #0: audiocodec
[    1.759387]   #1: sndhdmi
[    1.761141] Freeing init memory: 320K
[    2.349521] vmouse_input_dev_open
[    2.380259] vmouse_input_dev_close
[    3.032533] EXT4-fs (mmcblk0p1): mounted filesystem with writeback data mode. Opts: (null)
[    3.659515] systemd[1]: System time before build time, advancing clock.
[    4.190542] systemd[1]: systemd 229 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[    4.191161] systemd[1]: Detected architecture arm.
[    4.221840] systemd[1]: Set hostname to <orangepizero>.
[    4.842674] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    4.860791] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[    4.880558] systemd[1]: Listening on udev Kernel Socket.
[    4.900950] systemd[1]: Listening on Journal Audit Socket.
[    4.920334] systemd[1]: Reached target Remote File Systems (Pre).
[    4.940608] systemd[1]: Listening on Journal Socket (/dev/log).
[    4.961403] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    4.980662] systemd[1]: Listening on Journal Socket.
[    5.001158] systemd[1]: Created slice User and Session Slice.
[    5.020350] systemd[1]: Reached target Encrypted Volumes.
[    5.040399] systemd[1]: Reached target Remote File Systems.
[    5.060976] systemd[1]: Created slice System Slice.
[    5.190722] systemd[1]: Starting Nameserver information manager...
[    5.310942] systemd[1]: Created slice system-serial\x2dgetty.slice.
[    5.431183] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[    5.620552] systemd[1]: Mounting POSIX Message Queue File System...
[    5.821191] systemd[1]: Starting Set console keymap...
[    5.961423] systemd[1]: Starting Load Kernel Modules...
[    6.108144] [XRADIO] Driver Label:L34M.01.08.0002  Nov  9 2016 22:04:34
[    6.108264] [XRADIO] Allocated hw_priv @ c4bff240
[    6.108523] [XRADIO_ERR] Access_file failed, path:/data/xr_wifi.conf!
[    6.109310] [SBUS] XRadio Device:sdio clk=50000000
[    6.109642] xradio wlan power on
[    6.109676] gpio wl_reg_on set val 1, act val 1
[    6.140744] systemd[1]: Mounting Debug File System...
[    6.159730] gpio wl_reg_on set val 0, act val 0
[    6.160908] systemd[1]: Listening on Syslog Socket.
[    6.161763] gpio wl_reg_on set val 1, act val 1
[    6.251177] systemd[1]: Starting Restore / save the current clock...
[    6.261874] [XRADIO] Detect SDIO card 1
[    6.270881] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[    6.290876] systemd[1]: Listening on udev Control Socket.
[    6.310417] systemd[1]: Reached target Slices.
[    6.330478] systemd[1]: Listening on fsck to fsckd communication Socket.
[    6.401220] systemd[1]: Starting Remount Root and Kernel File Systems...
[    6.490769] EXT4-fs (mmcblk0p1): re-mounted. Opts: commit=600,errors=remount-ro
[    6.516200] systemd[1]: Mounted POSIX Message Queue File System.
[    6.530602] systemd[1]: Mounted Debug File System.
[    6.608405] [XRADIO_ERR] xradio_load_firmware: can't read config register, err=-110.
[    6.608439] [XRADIO_ERR] xradio_load_firmware failed(-110).
[    6.944713] xradio wlan power off
[    6.944748] gpio wl_reg_on set val 0, act val 0
[    6.994805] [XRADIO] Remove SDIO card 1
[    6.995064] mmc1: card 0001 removed
[    6.995504] [mmc]: sdc1 power_supply is null
[    7.000352] systemd[1]: Started Create list of required static device nodes for the current kernel.
[    7.160317] systemd[1]: Started Set console keymap.
[    7.181460] systemd[1]: systemd-modules-load.service: Main process exited, code=exited, status=1/FAILURE
[    7.360213] systemd[1]: Failed to start Load Kernel Modules.
[    7.400260] systemd[1]: systemd-modules-load.service: Unit entered failed state.
[    7.400475] systemd[1]: systemd-modules-load.service: Failed with result 'exit-code'.
[    7.530249] systemd[1]: Started Restore / save the current clock.
[    7.690237] systemd[1]: Started Remount Root and Kernel File Systems.
[    7.861074] systemd[1]: Started Nameserver information manager.
[    7.987147] systemd[1]: Time has been changed
[    8.151413] systemd[1]: Starting udev Coldplug all Devices...
[    8.321347] systemd[1]: Starting Load/Save Random Seed...
[    8.460600] systemd[1]: Activating swap /var/swap...
[    8.601247] systemd[1]: Starting Apply Kernel Variables...
[    8.641680] Adding 131068k swap on /var/swap.  Priority:-1 extents:2 across:204796k SS
[    8.720624] systemd[1]: Mounting FUSE Control File System...
[    8.861193] systemd[1]: Starting Create Static Device Nodes in /dev...
[    8.880995] systemd[1]: Activated swap /var/swap.
[    8.906051] systemd[1]: Mounted FUSE Control File System.
[    9.520497] systemd[1]: Started Load/Save Random Seed.
[    9.690327] systemd[1]: Started Apply Kernel Variables.
[    9.870248] systemd[1]: Started Create Static Device Nodes in /dev.
[   10.010258] systemd[1]: Started udev Coldplug all Devices.
[   10.161096] systemd[1]: Starting udev Kernel Device Manager...
[   10.180459] systemd[1]: Reached target Local File Systems (Pre).
[   10.330684] systemd[1]: Mounting /tmp...
[   10.350669] systemd[1]: Reached target Swap.
[   10.427590] systemd[1]: Mounted /tmp.
[   10.442062] systemd[1]: Started udev Kernel Device Manager.
[   10.450791] systemd[1]: Reached target Local File Systems.
[   10.510956] systemd[1]: Starting Raise network interfaces...
[   10.621427] systemd[1]: Starting Set console font and keymap...
[   10.751427] systemd[1]: Started Entropy daemon using the HAVEGE algorithm.
[   10.871501] systemd[1]: Starting Journal Service...
[   10.941075] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x77)
[   10.941165] bmp085: probe of 0-0077 failed with error -70
[   10.949746] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x48)
[   10.950138] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x48, dev addr: 0x48)
[   11.124875] systemd[1]: Found device /dev/ttyS0.
[   11.129979] vmouse_input_dev_open
[   11.152406] systemd[1]: Started Journal Service.
[   11.221231] vmouse_input_dev_close
[   11.773581] systemd-journald[234]: Received request to flush runtime journal from PID 1
[   11.992481] gmac0: probed
[   11.992918] gmac0 gmac0: eth0: eth0: PHY ID 00441400 at 0 IRQ poll (gmac0-0:00)
[   15.990281] PHY: gmac0-0:00 - Link is Up - 100/Full
root@orangepizero:~#

JR川崎駅から一番近い久寿餅販売所は駅構内のキオスクだった


久々に川崎大師の久寿餅が食べたくなった。

川崎大師の近辺にいくと何店舗があり、微妙に異なる久寿餅が手に入る
参考→ 適当に生きてます!「地元 川崎大師のくず餅 6店舗を食べ比べてみた!」(2014年8月14日)

店舗差はさておき、JR川崎乗り換えのついでに買えるところが無いか、とりあえずtwitterで聞いて見た。

さっそく現地調査!
JR川崎駅について、階段あがって改札を出る前に、構内にあるキオスクを確認


売ってますね。
改札出なくても買えました。
川崎大師の山門の目の前にある、独鈷の方の「住吉」

— 2018/08/13 追記 —
川崎駅の北側にある構内にあるNEWDAYSと成城石井では販売していません。
南側だとキオスクとNEWDAYSの両方で独鈷の住吉を販売しています。
— 追記終わり —

でも、せっかくもらった情報なので、確認してみようと、改札を出てみると、出口改札と入口改札の間にあるキオスクでも販売を確認。


こちらも独鈷の方の「住吉」

— 2018/08/13 追記 —
中央通路のキオスクは現在閉店中。
北口通路にはNEWDAYSがあり、そこでは独鈷の住吉を販売中。
— 追記終わり —

続いて、東口地下街のアゼリアへ。
エスカレータ降りて右奥にある川崎銘菓コーナで発見。

ここも独鈷の方の「住吉」でした。
ここは、久寿餅以外にもおまんじゅうやあんみつなども取り扱っています。

さて、最後に西口のラゾーナ川崎
こちらは、探しましたがありませんでした。
というか、川崎の地元のお店が1店舗しかなく、それ以外は別の地域からの出店ばかりだったような・・・

というわけで、JR川崎駅から一番近いのは、キオスクで販売してる「住吉」の独鈷の久寿餅でした。

さて・・・

リバティ会津ができて快速は半分以上消えるのではないか?→全廃



2017/03/02追記

4月21日(金) ダイヤ改正を実施!東武スカイツリーライン・伊勢崎線・日光線・鬼怒川線など【特急列車以外の一般列車】」が公開されました。

快速/区間快速が全部なくなりました。
今後、浅草から会津方面に行くには「南栗橋」「下今市」と、場合によっては「鬼怒川温泉」で乗り換える必要があるようです・・・


日光行きの急行電車を補完するために、下今市~鬼怒川温泉だけの短区間列車は走らせたくないようで、いくつか日光~下今市~鬼怒川温泉、という列車にするようです。

東武ワールドスクエア駅の告知に掲載されているダイヤを見ると、いろんなパターンがありそうです・・・

これをこのページの下の方にある時刻表に反映させるとこんな感じになります。

特急に乗らずに安くいこうという人には最悪な改正となり、ここまで乗り換え回数が増えてしまうんだったら、高速バスで行きますよ・・・


東京から会津若松にいくのに、時々、会津鉄道経由で行くことがある。
快速だと北千住からだと、時期により座れない可能性があるため、行きは特急で
帰りは始発駅から乗れるので、快速、という感じで使っている。

2017年4月21日のダイヤ改正で、リバティ会津という特急電車が登場し、今回、特急のダイヤが発表された。
東武鉄道リリースpdf「2017年 4月 21日 (金 ) ダイヤ改正を実施!東武スカイツリーライン・伊勢崎線・日光線・東武アーバンパークライン【特急列車概要 】

しかし、この発表の中では、特急列車以外については後ほど、と書かれており、快速がどのようになるのか記載されていない。

関連する野岩鉄道会津鉄道では、どのようなリリースが出ているかを確認してみる。

野岩鉄道リリースpdf「2017年4月21日(金)ダイヤ改正を実施します!「 特 急 リ バ テ ィ 会 津 」運 転 概 要
ここでは、野岩鉄道区間を通って会津鉄道会津田島駅までの話で終わっており、東武鉄道のリリースpdfとさほど変わらない内容となっている。

会津鉄道リリースpdf「平成29年4月ダイヤ改正について

こちらでは、会津若松までの連絡も含めた記載がされており、会津田島~会津若松は、「リレー号」という名称の列車を運行する、という記載がある。

そして、従来の特急乗り継ぎとの対比がされている。
この対比表を元に、快速についても追加したものを作成してみた

浅草駅12時頃出発~会津若松17時頃到着、という列車がない以外は、ほぼ従来の特急/快速乗り継ぎパターンが、新しいリバティ会津に置き換わっていることがわかる。

この区間は、リバティ会津は、列車によっては各駅に止まるものもあるようだが、いくらかは駅を飛ばしていくようだ。

リバティ会津以外にも普通列車が運行されるとは思われるが、野岩鉄道~会津鉄道の電車区間は、同時運行できる電車本数が限られている、という話がある。
このことを考えると、この区間を走る電車本数はそれほど変わらない可能性が高い。
つまりは、従来の快速(野岩鉄道~会津鉄道区間は各駅停車)は、かなり減るのではないか?と想定されます。

はたして・・・どうなることか・・・

Windows IoTに対応したOrange Pi Winがリリースされる???



githubのOrange Pi LibraにあるOrange Piボード用のSDKには「Orange Pi H5 SDK」「Orange Pi H2 SDK」「Orange Pi A64 SDK」の3種類がある。

Orange Pi A64 SDKは、H5を採用する前のテストボード用で、製品はリリースされない、と思っていたのですが、build.shをよくよく見てみると気になる記載が・・・

build.shの95行~99行目に「OrangePi Win」と「OrangePi 3(internal version)」の2機種が・・・

内部向けと書かれているOrange Pi 3はともかく、気になるのは、Orange Pi Win

同じくAllwinner A64を採用しているBananaPiのBPI-M64とPINE64は、Windows IoTに対応しています。(参考:Allwinner A64搭載ボードのBPI-M64とPINE64がWindows 10 IoTに対応開始。記事は2016/08/04に書いたものだが、2017/01/06時点でもGet Startedには記載が無いがgithubを見に行くと手順書は存在している)

これは、Orange Piの方でもWindows IoTに対応したボードを出そうという意気込みなのか?と期待してしまいます。


ちなみに、当blogでは記事にしていませんでしたが、2016/12/24にFriendlyARMからAllwinner A64搭載のNanoPi A64の情報も出ています。

FriendlyARMのAllwinner A64 SDK:「https://github.com/friendlyarm/a64_lichee
搭載ボード情報:「NanoPi A64

NanoPi A64の最大のトピックは、Allwinner A64搭載ボードでは最小サイズ、といったところでしょうか

Allwinner H5が登場したとこで、Allwinner A64の出番が減るかと思っていたのですが、PINE64を始めとした製品が出てから1年以上が経過したいまになって、採用製品が増え出す、というのはちょっと意外な感じです。

LicheePi OneとLicheePi Zero



Allwinner系SoCを使ったLinuxを扱う場合に基礎となるLinux-sunxiを見ていたら、見慣れないプロダクトを2つ発見
LicheePi One
LicheePi Zero

ぱっと見た感じだと、ディスプレイ出力ができるLicheePi Oneと、シリアル出力のみのLiecheePi Zeroなのかな?と思ったのですが、よく見てみると全然違いました・・・

LiecheePi One
CPUが古く、Cortex-A8のAllwinner A13搭載。
CHIPSで使っているAllwinner R8の前身となるSoCを使用。
HDMIコネクタは無いが、フラットケーブル接続で液晶パネルがつけられる。

https://github.com/Zepan/ilicheeに関連資料がある。

cnx-softwareでLichee Pi Oneは6ドル、という記事があったが、作者によれば、6ドル、というのは誤りだそうな。

LicheePi Zero
CPUはCortex-A7のAllwinner V3s搭載。
Orange Pi Oneなどで使用しているAllwinner H3からGPU機能などを抜き、車載カメラやIPカメラ用にしたSoCを使用。
RAMは64MBと限られている。
ESP8266モジュールのような感じでブレッドボードにさして使える感じのもの。
標準ではLANコネクタは無く、またWiFiも搭載されていない。
「Network: 10/100Mbps Ethernet (via extension board, not available now)」とあるので、別途取り付けはできるようになる模様。

対応するLinux kernelは、https://github.com/Icenowy/linux/tree/v3sで公開されている。U-Bootについても同じ作者が開発中

作者によると、Lichee Pi Zeroは6ドルぐらいで販売できるらしい。